|
|
|
Question : Problem: Unable to configure 1130AG Access Point
|
|
I have two if these...one was NIB and it configured with no problems; the other was a "pull" from an office that was only up for a couple months. It worked flawlessly when first deployed. Now, I am unable to configure the device after performing a reset [Hold MODE button for approx. 2-sec after inserting plug until light turns amber, then release].
I can't PING via MAC address, there is nothing that comes up in my DHCP pool, the IPSU can't find the device, and I get the following data when attempting to connect via HyperTerminal:
Xmodem file system is available.
flashfs[0]: 136 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 4445184
flashfs[0]: Bytes available: 11553792
flashfs[0]: flashfs fsck took 28 seconds.
Base ethernet MAC Address: 00:15:c6:ff:44:0c
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1130-k9w7-mx.123-7.JA2/c1130-k9w7-mx.123-7.JA2"...#############
################################################################################
################################################################################
################################################################################
################################################################################
#############
File "flash:/c1130-k9w7-mx.123-7.JA2/c1130-k9w7-mx.123-7.JA2" uncompressed and i
nstalled, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(7)JA2, RELEASE S
OFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 18-Nov-05 12:37 by ssearch
Image text-base: 0x00003000, data-base: 0x00683980
Initializing flashfs...
flashfs[1]: 136 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 4445184
flashfs[1]: Bytes available: 11553792
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1131AG-A-K9 (PowerPCElvis) processor (revision A0) with 24566K/81
92K bytes of memory.
Processor board ID FOC0943329R
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:15:C6:FF:44:0C
Part Number : 73-8962-09
PCA Assembly Number : 800-24818-08
PCA Revision Number : A0
PCB Serial Number : FOC0943329R
Top Assembly Part Number : 800-25544-04
Top Assembly Serial Number : FTX0953T0HV
Top Revision Number : A0
Product/Model Number : AIR-AP1131AG-A-K9
Press RETURN to get started!
*Mar 1 00:00:06.653: %DOT11-4-LOADING_RADIO: Interface Dot11Radio1, loading the
radio firmware (flash:/c1130-k9w7-mx.123-7.JA2/6701.img)
*Mar 1 00:00:07.730: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
eset
*Mar 1 00:00:09.787: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:09.789: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar 1 00:00:10.789: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to up
*Mar 1 00:00:28.855: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to a
dministratively down
*Mar 1 00:00:28.858: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
dministratively down
*Mar 1 00:00:28.897: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power s
ource
*Mar 1 00:00:28.921: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(7)JA2, RELEASE S
OFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 18-Nov-05 12:37 by ssearch
*Mar 1 00:00:28.921: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a c
old start
*Mar 1 00:00:29.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to down
*Mar 1 00:00:29.858: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Mar 1 00:00:29.884: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
***********
What am I missing? or is this device dead?
|
Answer : Problem: Unable to configure 1130AG Access Point
|
|
The above output DOESNT show a reset of configuration!
When you press sucesffully the "MODE" button you get a message "Ignoring config" or something like that.... This is not the case
In any case. you should get access to the console port and get a password promt
Try to reset the access point, try to push "MODE" button several times the first seconds it boots
|
|
|
|
|
